Keysight N109310CA Electrical TX Test SW for SFF-8431 (SFP+)
Key Features
Comprehensive compliance and debug solution for SFP+ applications
- Addresses all seven test groups for host, host copper, and module transmit tests, and for receiver test signals
- Measures all of the ~70 parameters
- Convenient utilities to de-skew cables
Flexible and extensible
- Operate on an N1000A/86100D DCA-X oscilloscope, or on a PC connected to an N109x DCA-M via USB
- Control device under test and other equipment
- Test all or selected parameters to compliance limits or custom limits for development
Compatibility
- N1000A/86100D DCA-X Mainframe
- N109X DCA-M Oscilloscope
- N107X Clock Recovery
Addtional documents and Software Solutions:
Reduce your test time from hours to minutes. Use the N109310CA Electrical TX Test SW for SFF-8431 (SFP+) to measure your high speed serial host board, module or IC to all required transmit parameters in the SFF-8431 (SFP+) Specifications.
Keysight offers a wide range of electrical and optical test solutions to address current and emerging communications standards. For SFF-8431 (SFP+), you may choose a hardware combination that addresses your test needs for today, and into the future:
- N1000A/86100D DCA-X with N1060A/86108B (Integrated “One-Box” solution) - recommended
- N1000A/86100D DCA-X with DCA module and external clock recovery
- N109X Electrical DCA-M with external clock recovery
Seven SFF-8431 Interfaces
- Host transmitter output
- Module receiver output
- Host transmitter output for Cu
- Host receiver limiting module test signal
- Host receiver linear module test signal
- Module transmit input signal
- Host receiver stress generator
About 70 Tests
- Signaling rate
- Rise and fall times for outputs and crosstalk
- Differential, single-ended, crosstalk and common mode amplitudes
- Common mode noise
- Jitter: Total, DDJ, UJ, Qsq, 99%, DDPWS
- TWDP (through user-provided script)
- Eye mask
- Differential and common mode S-parameter
- Differential to common mode conversion loss
Time-Saving Features
- Complete additional extensive development testing using Debug mode
- De-skew cable length skew
- Control device under test
- Interface with other equipment
Reduce your test time from hours to minutes. Use the N109310CA Electrical TX Test SW for SFF-8431 (SFP+) to measure your high speed serial host board, module or IC to all required transmit parameters in the SFF-8431 (SFP+) Specifications.
Keysight offers a wide range of electrical and optical test solutions to address current and emerging communications standards. For SFF-8431 (SFP+), you may choose a hardware combination that addresses your test needs for today, and into the future:
- N1000A/86100D DCA-X with N1060A/86108B (Integrated “One-Box” solution) - recommended
- N1000A/86100D DCA-X with DCA module and external clock recovery
- N109X Electrical DCA-M with external clock recovery
Seven SFF-8431 Interfaces
- Host transmitter output
- Module receiver output
- Host transmitter output for Cu
- Host receiver limiting module test signal
- Host receiver linear module test signal
- Module transmit input signal
- Host receiver stress generator
About 70 Tests
- Signaling rate
- Rise and fall times for outputs and crosstalk
- Differential, single-ended, crosstalk and common mode amplitudes
- Common mode noise
- Jitter: Total, DDJ, UJ, Qsq, 99%, DDPWS
- TWDP (through user-provided script)
- Eye mask
- Differential and common mode S-parameter
- Differential to common mode conversion loss
Time-Saving Features
- Complete additional extensive development testing using Debug mode
- De-skew cable length skew
- Control device under test
- Interface with other equipment